How do you actually feel on the subject of A Step-by-Step Guide to Installing a Bathtub?
Installing a bath tub isn't exactly brain surgery, however it does require solid plumbing, carpentry, and also often, tiling abilities. Changing an old tub with a new one is likewise a moderately hard task. If the old tub is readily accessible, the project can relocate quickly; if you need to open up a wall surface to remove the old bathtub as well as position the brand-new bath tub, the task is much harder. In either instance, the task is within a house handyman's abilities, although you will certainly need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the job and fit trying it. Rather than hiring a professional to take over a halfway-completed project, it is better to take into consideration utilizing one before you start. Possibilities are you may require a professional plumber to make tube links.
This short article will certainly aid you set up a brand-new bath tub in your bathroom if you have currently acquired a brand-new bathtub and don't need to change the plan of your previous supply of water pipelines.
Your tools as well as material list ought to consist of the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, switch on the taps to drain any type of water remaining in the system. The procedure of removing the existing faucets can be rather bothersome because of the limited gain access to that is often the case.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric all set for the staying water that will come from the pipelines. When the supply pipes have been gotten rid of, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this procedure. Once the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to moving on to fit the new faucets, compare the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to avoid damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end gives a link to the current supply pipelines.
If you require to fit a monobloc, then you will call for decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the placing hole in the bath/basin making sure that the washing machines are in location between the faucet and also the sink. Secure the tap in place with the manufacturer provided backnut. As soon as the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The former type ought to be linked to the tap finishes first, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bath tub
Using both wood boards under its feet, place the bath tub in the needed placement. The wooden boards are practical in equally spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 small factors.
The following objective is to ensure that the bathtub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the tub till the spirit level reads degree.
To install taps, fit all-time low of the furthest versatile faucet connector to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the water system and also check all joints and also brand-new pipework for leakages as well as tighten them if essential. Load the bathtub and also inspect the overflow electrical outlet and also the typical electrical outlet for leaks.
Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling and sealing around the bathtub ought to wait until the bathtub has been made use of at the very least when as this will settle it into its final position.
Getting ready for the Setup
First of all, the supporting frame supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to see to it that if the tap includes a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps unit to stop strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two taps utilizing 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its final position.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to split an inflexible seal, creating the water to penetrate the wall surface in between the bathroom and also the tiling, leading to complications with dampness as well as feasible leaks to the ceiling below.
You can choose from a range of coloured sealants to blend in your fixtures as well as installations. They are offered in tubes and also cartridges, and are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to enable the motion experienced when the bathtub is in use. The sealant can split relatively early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was brought to that editorial about Tools You Need to Install a New Bathtub through someone on a different web property. In case you enjoyed our blog post plz make sure you remember to share it. Thanks a lot for taking the time to read it.
Call for peace of mind!